Refer to the exhibit. A new PC was deployed in the Sales
network. It was given the host address of 192.168.10.31 with a default gateway
of 192.168.10.17. The PC is not communicating with the network properly. What
is the cause?
• 192.168.10.31 is the broadcast address for this subnet.
Refer to exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on the Paris router? (Choose three.)
• Paris(config)# router eigrp 100
• Paris(config-router)# network 192.168.7.0
• Paris(config-router)# network 192.168.8.0
Refer to the exhibit. What two statements are true based on the output shown? (Choose two.)
• neighbors 192.168.10.9 and 192.168.10.5 have auto summary disabled.
• router 3 is load balancing traffic to the 172.16.3.0 network across its serial interfaces.
• 192.168.10.31 is the broadcast address for this subnet.
Refer to exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on the Paris router? (Choose three.)
• Paris(config)# router eigrp 100
• Paris(config-router)# network 192.168.7.0
• Paris(config-router)# network 192.168.8.0
Refer to the exhibit. What two statements are true based on the output shown? (Choose two.)
• neighbors 192.168.10.9 and 192.168.10.5 have auto summary disabled.
• router 3 is load balancing traffic to the 172.16.3.0 network across its serial interfaces.
Refer to the exhibit. The ORL router is unable to form a
neighbor relationship with the JAX router. What is a possible cause of this
problem?
• The command network 192.168.2.0 is missing from the EIGRP configuration on the JAX router.
Which statement is true regarding routing metrics?
• Routers compare metrics to determine the best route.
• The command network 192.168.2.0 is missing from the EIGRP configuration on the JAX router.
Which statement is true regarding routing metrics?
• Routers compare metrics to determine the best route.
Refer to the exhibit. The routers in the exhibit are running the EIGRP routing protocol. What statement is true regarding how packets will travel from the 172.16.1.0/16 network to the 192.168.200.0/24 network?
• The router installs all the equal cost paths in the routing table and performs equal cost load balancing to send packets out multiple exit interfaces.
. Which of the following could describe the devices labeled
"?" in the graphic? (Choose three.)
• DCE
• CSU/DSU
• Modem
• DCE
• CSU/DSU
• Modem
. Refer to exhibit. A company network engineer enters the
following commands in the routers:R1(config)# ip route 10.1.1.0 255.255.255.0
192.168.0.2R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1When the
engineer enters the show ip route command on R1, the routing table does not
display the static route to the 10.1.1.0 network. All R1 and R2 interfaces are
correctly addressed per the graphic. What is a logical next step that the
engineer could take in order to make the static route display in the routing
table in R1?
• Enable the R1 and R2 serial interfaces
• Enable the R1 and R2 serial interfaces
A network administrator has enabled RIP on routers B and C
in the network diagram. Which of the following commands will prevent RIP
updates from being sent to Router A?
• B(config)# router rip
B(config-router)# passive-interface S0/0
• B(config)# router rip
B(config-router)# passive-interface S0/0
Refer to the exhibit. The network is running the RIP routing
protocol. Network 10.0.0.0 goes down. Which statement is true regarding how the
routers in this topology will respond to this event?
• Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0.
• Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0.
. Refer to the exhibit. The network administrator issues the
command no ip classless on Router1. What forwarding action will take place on a
packet that is received by Router1 and is destined for host 192.168.0.26?
• The packet will be dropped.
• The packet will be dropped.
Using default settings, what is the next step in the router boot
sequence after the IOS loads from flash?
• Locate and load the startup-config file from NVRAM.
• Locate and load the startup-config file from NVRAM.
What does RIP use to reduce convergence time in a larger
network?
• It uses triggered updates to announce network changes if they happen in between the periodic updates.
• It uses triggered updates to announce network changes if they happen in between the periodic updates.
When presented with multiple valid routes to a destination,
what criteria does a router use to determine which routes to add to the routing
table?
• The router first selects routes with the lowest administrative distance. The resulting routes are then prioritized by metric and the routes with the best metric are added to the routing table.
• The router first selects routes with the lowest administrative distance. The resulting routes are then prioritized by metric and the routes with the best metric are added to the routing table.
Refer to the exhibit. Hosts on the BOS Fa0/0 LAN are able to
ping the Fa0/1 interface on the JAX router and all interfaces on the BOS and
ORL routers. Why would hosts from the 10.0.0.0/24 network not be able to ping
hosts on the Fa0/0 LAN of the JAX router?
• The JAX router needs the network 10.0.0.0 0.0.0.255 area 0 command.
• The JAX router needs the network 10.0.0.0 0.0.0.255 area 0 command.
What command would the network administrator apply to a
router that is running OSPF to advertise the entire range of addresses included
in 172.16.0.0/19 in area 0?
• R1(config-router)# network 172.16.0.0 0.0.31.255 area 0
• R1(config-router)# network 172.16.0.0 0.0.31.255 area 0
Refer to the exhibit. Which statement is true concerning the
routing configuration?
• Packets routed to the R2 ethernet interface require two routing table lookups.
Refer to the exhibit. All routers in the network are running RIPv2 and EIGRP with default routing protocol settings and have interfaces configured with the bandwidths that are shown in the exhibit. Which protocol will be used and how will traffic between the Router1 LAN and Router5 LAN be routed through the network?
• EIGRP traffic will use the path Router1, Router3, Router4, Router5 because it has the best metric.
• Packets routed to the R2 ethernet interface require two routing table lookups.
Refer to the exhibit. All routers in the network are running RIPv2 and EIGRP with default routing protocol settings and have interfaces configured with the bandwidths that are shown in the exhibit. Which protocol will be used and how will traffic between the Router1 LAN and Router5 LAN be routed through the network?
• EIGRP traffic will use the path Router1, Router3, Router4, Router5 because it has the best metric.
Which two router component and operation pair are correctly
described? (Choose two.)
• NVRAM -stores the configuration file
• POST -runs diagnostics on hardware modules
• NVRAM -stores the configuration file
• POST -runs diagnostics on hardware modules
Which of the following are primary functions of a router?
(Choose two.)
• packet switching
• path selection
• packet switching
• path selection
Which two statements are true regarding link-state routing
protocols? (Choose two.)
• They are aware of the complete network topology.
• They offer rapid convergence times in large networks.
• They are aware of the complete network topology.
• They offer rapid convergence times in large networks.
Which three statements about routing protocols are true?
(Choose three.)
• OSPF elects designated routers on multiaccess links.
• EIGRP supports unequal cost load balancing.
• RIP does not advertise a route beyond a hop count of 15.
What command would the network administrator apply to a router that is
running OSPF to advertise the entire range of addresses included in
172.16.0.0/19 in area 0? • OSPF elects designated routers on multiaccess links.
• EIGRP supports unequal cost load balancing.
• RIP does not advertise a route beyond a hop count of 15.
• *R1(config-router)# network 172.16.0.0 0.0.31.255 area 0
Refer to the exhibit. A new PC was deployed in the Sales network. It was given the host address of 192.168.10.31 with a default gateway of 192.168.10.17. • The PC is not communicating with the network properly. What is the cause?
• The host address and default gateway are swapped.
Refer to exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on the Paris router? (Choose three.)
• Paris(config)# router eigrp 100
• Paris(config-router)# network 192.168.7.0
• Paris(config-router)# network 192.168.8.0
Which three statements about routing protocols are true?
(Choose three.)
• OSPF elects designated routers on multiaccess links.
• EIGRP supports unequal cost load balancing.
• RIP does not advertise a route beyond a hop count of 15.
Which of the following are primary functions of a router? (Choose two.) • OSPF elects designated routers on multiaccess links.
• EIGRP supports unequal cost load balancing.
• RIP does not advertise a route beyond a hop count of 15.
• packet switching
• path selection
What are three features of CDP? (Choose three.)
• tests Layer 2 connectivity
• enabled by default on each interface
• provides information on directly connected devices that have CDP enabled
Refer to the exhibit. All routers in the network are running RIPv2 and EIGRP with default routing protocol settings and have interfaces configured with the bandwidths that are shown in the exhibit. Which protocol will be used and how will traffic between the Router1 LAN and Router5 LAN be routed through the network?
• RIPv2 traffic will use the path Router1, Router2, Router5 because it has the least hops.
Which three statements describe the operation of routing with EIGRP? (Choose three.)
• As new neighbors are discovered, entries are placed in a neighbor table.
• If hello packets are not received within the hold time, DUAL must recalculate the topology.
• The reported distance is the distance to a destination as advertised by a neighbor.
The administrator knows that port E0 on router B connects to
a small LAN without any routers. Which command can be executed on router B to
conserve bandwidth on port E0?
# passive-interface E0
# passive-interface E0
The commands shown in the graphic were entered to alter the startup
sequence of the router. On the next reload, which IOS will be loaded?
# The router will boot into ROM monitor mode.
# The router will boot into ROM monitor mode.
Why would an administrator use the Telnet application when troubleshooting a network? (Choose three.)
# It can be used to verify the operation of application layer software between the source and destination.
# It is the most complete testing mechanism available.
# Remote networks may be accessed via a Telnet session for troubleshooting.
# It can be used to verify the operation of application layer software between the source and destination.
# It is the most complete testing mechanism available.
# Remote networks may be accessed via a Telnet session for troubleshooting.
